lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y features * super thin (0.30 mm) chip led. * ultra bright ingan white chip led. * package in 8mm tape on 7" diameter reels. * compatible with automatic placement equipment. * compatible with infrared and vapor phase reflow s older process. * eia std package. * i.c. compatible. package dimensions part no. lens emitted color LTW-C194TS5 yellow ingan white notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.10 mm (.004") unless otherwise noted. part no. : LTW-C194TS5 page : 1 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at ta=25 parameter LTW-C194TS5 unit power dissipation 70 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 100 ma dc forward current 20 ma reverse voltage 5 v operating temperature range -20 c to + 80 c storage temperature range -55 c to + 105 c soldering temperature 260 c for 5 seconds suggest ir reflow condition : r e c o m m e n d e d p r o f ile b e t w e e n a s s e m b le a n d h e a t -r e s is t a n c e l in e t h e p ro file is a v a ila b le th a t m u s t to u s e s n a g c u s o ld e r p a s te part no. : LTW-C194TS5 page : 2 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical optical characteristics at ta=25 parameter symbol part no. ltw- min. typ. max. unit test condition luminous intensity iv c194ts5 56.0 146.0 mcd if = 5ma note 1, 2, 5 viewing angle 2 1/2 c194ts5 130 deg fig.6 x 0.294 chromaticity coordinates y c194ts5 0.286 if = 5ma note 3, 5 fig.1 forward voltage vf c194ts5 2.70 3.15 v if = 5ma reverse current ir c194ts5 10 a vr = 5v note : 1. luminous intensity is measured with a lig ht sensor and filter combination that approximates the cie eye-response curve. 2. iv classification code is marked on each packing bag. 3. the chromaticity coordinates (x, y) is derived f rom the 1931 cie chromaticity diagram. 4. caution in esd: static electricity and surge damages the led. it is recommend to use a wrist band or anti-electrostati c glove when handling the led. all devices, equipment and machinery must be properly grounded. 5. tester cas140b is for the chromaticity coordinates (x, y) and iv. 6. the chromaticity coordinates (x, y) guarantee sh ould be added 0.01 tolerance. part no. : LTW-C194TS5 page : 3 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics c urves (25 ambient temperature unless otherwise noted ) part no. : LTW-C194TS5 page : 4 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y bin code list part no. : LTW-C194TS5 page : 5 of 10 bns-od-c131/a4 vf spec. table forward voltage (v) at if = 5ma vf bin min. max. a 2.70 2.85 b 2.85 3.00 c 3.00 3.15 tolerance on each forward voltage bin is +/-0.1 vol t iv spec. table luminous intensity (mcd) at if = 5ma iv bin min. max. p2 56.0 71.0 q1 71.0 90.0 q2 90.0 112.0 r1 112.0 146.0 tolerance on each luminous intensity bin is +/- 15% . hue spec. table color bin limits at if = 5ma hue bin cie 1931chromaticity coordinates x 0.274 0.274 0.294 0.294 s1 y 0.226 0.258 0.286 0.254 x 0.274 0.274 0.294 0.294 s2 y 0.258 0.291 0.319 0.286 x 0.294 0.294 0.314 0.314 s3 y 0.254 0.286 0.315 0.282 x 0.294 0.294 0.314 0.314 s4 y 0.286 0.319 0.347 0.315 x 0.314 0.314 0.334 0.334 s5 y 0.282 0.315 0.343 0.311 x 0.314 0.314 0.334 0.334 s6 y 0.315 0.347 0.376 0.343 tolerance on each hue (x, y) bin is +/- 0.01. c. i. e. 1931 chromaticity diagram 0.2 0.25 0.3 0.35 0.4 0.25 0.27 0.29 0.31 0.33 0.35 x-coordinate y-coordinate s2 s1 s4 s3 s6 s5
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y cleaning do not use unspecified chemical liquid to clean led they could harm the package. if clean is necessary, immerse the led in ethy l alcohol or in isopropyl alcohol at normal tempera ture for less one minute. suggest soldering pad dimensions notes: 1. suggest stencil thickness is maximum 0.10mm. package dimensions of tape and reel notes: 1. all dimensions are in millimeters (inches). part no. : LTW-C194TS5 page : 6 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y package dimensions of reel notes: 1. empty component pockets sealed with top cover ta pe. 2. 7 inch reel-3000 pieces per reel. 3. minimum packing quantity is 500 pieces for remai nders. 4. the maximum number of consecutive missing lamps is two. 5. in accordance with ansi/eia 481-1-a-1994 specifi cations. part no. : LTW-C194TS5 page : 7 of 10 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : LTW-C194TS5 page : 8 of 10 bns-od-c131/a4 cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household ap plications).consult liteons sales in advance for information on applications in which exceptiona l reliability is required, particularly when the fa ilure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation , traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original p ackaging are ir-reflowed within one week. for extended storage out of their original packagin g, it is recommended that the leds be stored in a sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient. leds stored out of their original packaging for mor e than a week should be baked at about 60 deg c for at least 24 hours before solder assembly. 3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the led if necessary. 4. soldering recommended soldering conditions: reflow soldering wave soldering soldering iron pre-heat pre-heat time peak temperature soldering time 120~150c 120 sec. max. 260c max. 5 sec. max. pre-heat pre-heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 10 sec. max. temperature soldering time 300c max. 3 sec. max. (one time only) 5. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connected in parallel in an application, it is reco mmended that a current limiting resistor be incorpo rated in the drive circuit, in series with each led as sh own in circuit a below. circuit model a circuit model b led led (a) recommended circuit. (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds. 6. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use of a conductive wrist band or anti-electrostati c glove when handling these leds. all devices, equipment, and machinery must be prope rly grounded. work tables, storage racks, etc. should be properly grounded. use ion blower to neutralize the static charge whic h might have built up on surface of the leds plastic lens as a result of friction between leds d uring storage and handling.
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : LTW-C194TS5 page : 9 of 10 bns-od-c131/a4 esd-damaged leds will exhibit abnormal characterist ics such as high reverse leakage current, low forwa rd voltage, or no lightup at low currents. to verify for esd damage, check for lightup and vf of the suspect leds at low currents. the vf of good leds should be >2.0v@0.1ma for i ngan product and >1.4v@0.1ma for alingap product. 7. reliability test classification test item test condition reference standard operation life ta= under room temperature as per data sheet maximum rating * test time= 500hrs (-24hrs,+72hrs)*@20ma. mil-std-750d:1026 mil-std-883d:1005 jis c 7021:b-1 high temperature high humidity storage ir-reflow in-board, 2 times ta= 655 ,rh= 90 95% * test time= 240hrs2hrs mil-std-202f:103b jis c 7021:b-11 high temperature storage ta= 1055 * test time= 500hrs (-24hrs,+72hrs) mil-std-883d:1008 jis c 7021:b-10 endurance test low temperature storage ta= -555 * test time=500hrs (-24hrs,+72h rs) jis c 7021:b-12 temperature cycling 105 25 -55 25 30mins 5mins 30mins 5mins 10 cycles mil-std-202f:107d mil-std-750d:1051 mil-std-883d:1010 jis c 7021:a-4 thermal shock ir-reflow in-board, 2 times 85 5 -40 5 10mins 10mins 10 cycles mil-std-202f:107d mil-std-750d:1051 mil-std-883d:1011 solder resistance t.sol= 260 5 dwell time= 10 1secs mil-std-202f:210a mil-std-750d:2031 jis c 7021:a-1 ir-reflow ramp-up rate(217 to peak) +3 / second max temp. maintain at 175(25) 180 seconds max temp. maintain above 217 60-150 seconds peak temperature range 260 +0/-5 time within 5c of actual peak temperature (tp) 20-40 seconds ramp-down rate +6 /second max mil-std-750d:2031.2 j-std-020 environmental test solderability t.sol= 235 5 immersion time 20.5 sec immersion rate 252.5 mm/sec coverage R 95% of the dipped surface mil-std-202f:208d mil-std-750d:2026 mil-std-883d:2003 iec 68 part 2-20 jis c 7021:a-2 8. others the appearance and specifications of the product ma y be modified for improvement without prior notice.
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y 9. suggested checking list training and certification 1. everyone working in a static-safe area is esd- certified? 2. training records kept and re-certification dat es monitored? static-safe workstation & work areas 1. static-safe workstation or work-areas have esd signs? 2. all surfaces and objects at all static-safe wo rkstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sens itive (esds) items wears wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibrati on up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. no static charge generators (e.g. plastics) insi de shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycles? others 1. audit result reported to entity esd control coor dinator? 2. corrective action from previous audits completed ? 3. are audit records complete and on file? part no. : LTW-C194TS5 page : 10 of 10 bns-od-c131/a4
|
